(TBS) iFlight BOB 57 All in one Drone + (GPS)

The pilot & videographer Ellisvanjason and iFlight teamed up to craft a cinematic 6 inch drone that ensures agility and flight time and therefore combines the advantages of both 5 inch and 7 inch drones.

659.99 

In stock

Use up to 660 points to purchase this product!

Description

The pilot & videographer Ellisvanjason and iFlight teamed up to craft a cinematic 6 inch drone that ensures agility and flight time and therefore combines the advantages of both 5 inch and 7 inch drones.

Features:

– 6 inch drone re-engineered: This drone was specifically designed for 6 inch

– H-shaped frame with robust middle section for less props in view while remaining stiffness

– XT60 front-mount: Compare to other drones the mount sits in the front and gives more space on the back.

– Built in BEC to directly power a gopro (no battery needed)

– Hybrid motor design: This motor is optimized for 6 inch. Can be used with bi- blades (efficiency) and tri-blades (agility & trust).

– Antenna mount: Solid antenna mount for less ocillations when using long antennas

– Long back bone: Enough space up to 3000mAh 6S batteries

– Gladiator shell: Protection shell from dust and water droplets (shall be removed for max. flight time)

– GPS: A high-end GPS is used to minimize the risk of failure during proximity flights

– ESC: The drone consists iFlight’s new ESCs with built-in spike absober for more reliability

– 9min flight time with 1800mAh 6S

– 9+ with 3000mAh 6S Lipo or 4000mAh 6S Li-Ion

– Get Ellisvanjason’s tune on ellisvanjason.com

Specifications:

– Upper(middle) plate thickness: 2.5mm

– Bottom plate thickness: 1.5mm

– Total Dimensions: 254*254mm

– Bottom to top distance: 22mm

– Geometry: H-shaped frame

– Top plate thickness: 2mm

– Ellisvanjason 2506 motors

– Gemfan 6032 propellers

– Arm Thickness: 6mm

ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC):

FC //BLITZ F722 Flight Controller

Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
Smartaudio / IRC Tramp VTX protocol supported
Firmware target: IFLIGHT_BLITZ_F722
Motor outputs: 4x (SH1.0 connector)
Flash: 32MB (Blackbox flash)
I2C serial: SDA / SLA pads
Dimensions: 36.5*35 mm
Barometer: DPS310
OSD Chip: AT7456E
LED controller: Yes
MCU: STM32 F722
Beeper pad: Yes
Gyro: BMI270
Weight: 7.8g
UARTS: 6
Product Link

ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
Mounting Holes: 30.5*30.5mm/Φ4mm
Target: IFLIGHT_BLITZ_G2
Supports 2-6S Lipo input
Current sensor: Yes
Constant: 55 Amps
Current rate: 200
Burst: 65 Amps
Weight: 15.3g
MCU: G071
BEC: No

Product Link

BOB57 HD Included Components and Parts

2 x GEMFAN 6032- CW propeller + 2 x 6032 CCW (Green)
2 x GEMFAN 6032- CW propeller + 2 x 6032 CCW (Black)
1 x Albatross LHCP 5.8GHz SMA FPV Antenna 150mm
1 x Albatross LHCP 5.8GHz SMA FPV Antenna 60mm
1 x USB Type-C 5V Balance Plug Power Cable 55mm
2 x iFlight Lipo Strap 20*250mm (Black)
1 x Nebula Pro Vista HD System
1 x Pre-built and Tested BOB57

Reviews

There are no reviews yet.

Earn 1 points by reviewing this product.
Be the first to review “(TBS) iFlight BOB 57 All in one Drone + (GPS)”

Your email address will not be published.